环氧／聚氨酯涂料的研究

采用环氧树脂来固化聚氨酯涂料，可使涂层具有良好的刚性和耐蚀性，本文研究了涂料各组分对于涂料涂层性能的影响，拟定了最佳配方工艺，并对其机理进行了阐述。     

聚氨酯改性环氧树脂的研究

用原位聚合法制备了聚氨酯/环氧树脂复合材料,考察了不同因素对刚性聚氨酯/环氧树脂复合材料力学性能的影响。结果表明,在所得复合材料中,当聚氨酯含量不高时,其冲击强度、拉伸强度和耐热稳定性能同时得到提高;若刚性聚氨酯含量超过一定范围,材料的拉伸强度逐渐降低。比较了聚酰胺、咪唑、三乙胺、三乙烯二胺四种固化剂的固化效果,结果表明,聚酰胺固化效果最好,咪唑的固化效果次之,三乙胺固化改性后的力学性能较差,而三乙烯二胺不能完全固化聚氨酯/环氧树脂复合材料。制得了拉伸强度为54.6MPa,冲击强度为12.025KJ.m-2的高韧性聚氨酯/环氧树脂复合材料。     

新型高残碳酚醛树脂的研究I.高残碳酚醛树脂的合成及其残碳率

合成了DA系列树脂改性剂和芳基改性酚醛树脂 ,并以DA改性剂改性芳基酚醛树脂。用热重、电子顺磁共振等方法研究了改性酚醛树脂的残碳率。研究表明 ,用DA改性剂来改性酚醛树脂是提高残碳率的有效方法 ,改性酚醛树脂的残碳率可达 6 9.87%。     

可溶性改性双马来酰亚胺树脂基体的研究

在双马来酰亚胺/二元胺/改性剂A预聚体系中加入环氧丙烯酸树脂,制备了一种可用作耐热复合材料基体的改性双马来酰亚胺树脂。用DSC研究了该树脂基体的反应特性,并制定出了合适的固化工艺参数:改性树脂基体经140℃/1 h 160℃/1 h 180℃/2 h初固化,于220℃/8 h后固化处理,其热变形温度(HDT)为245℃;该树脂与玻璃纤维制备的单向复合材料层压板的室温拉伸强度、弯曲强度和层间剪切强度分别为1 030 MPa、1 600 MPa和92．1 MPa;180℃下测得弯曲强度保持率为67．8%,层间剪切强度保持率为63．2%,用DMA法测得T_g为273℃。     

风电及高压电机用绝缘浸渍漆选型试验研究

选取国内常用的两种树脂与环氧酸酐浸渍树脂作对比测试。通过对树脂常规性能及浸渍模拟线圈电性能测试,得出结论:1号树脂具有较好的储存稳定性,电性能与环氧酸酐相当,可作为环氧酸酐的替代品。     

环境温湿度对蜂窝增强硅橡胶基低密度烧蚀材料硬度的影响

介绍了环境温湿度以及促进剂用量、酸酐用量对窝增强硅橡胶基低密度烧蚀材料硬度的影响。试验发现蜂窝增强硅橡胶基低密度烧蚀材料硬度沿厚度方向呈规律变化：从外向里材料硬度逐渐降低,室温存放时间长的材料硬度降低的梯度小;密度小的材料硬度降低梯度小;促进剂量多的材料硫化后材料表面硬度大,从外向里硬度降低梯度大。其酸酐用量最佳起来 环氧树脂的３０％（质量分数）。     

烧蚀材料用改性酚醛树脂

简介了几种烧蚀材料用改性酚醛树脂的结构，合成，性能及应用，以酚醛树脂改性已成为烧蚀材料基体树脂的发展方向之一。     

新型聚苯并噁嗪改性树脂的制备与性能

通过预聚反应制备了一种新型聚苯并噁嗪改性树脂.利用FTIR、GPC表征了改性树脂.利用旋转黏度计、DSC、DMA和TGA分别考察了树脂的流动性能、固化行为和改性树脂固化物的热性能.结果表明:制备的苯并噁嗪改性树脂在60～ 100℃,黏度小于500 mPa·s,恒温6h黏度不明显增大,具有良好的流动性能,适用于RTM成型工艺.改性树脂聚合温度较低,具有良好的固化工艺性.改性树脂固化物在氮气气氛下Td5在430℃以上,在900℃的残重高达73.71％,Ts为353.4℃,具有良好热性能.     

碳纳米管/玻纤/环氧层板超声真空灌注工艺及性能研究

针对碳纳米管/玻璃纤维/环氧树脂体系,采用传统的真空灌注工艺和超声波辅助真空灌注工艺制备复合材料层板,分析不同工艺方法下层板缺陷状况,测试层板的弯曲性能和层间剪切性能,考察树脂性能和纤维/树脂界面黏结状况,探讨碳管及工艺方法对层合板性能的影响。结果表明:与传统的真空罐注工艺相比,超声波辅助真空罐注工艺能增强树脂在纤维内部的流动,提高树脂对纤维的浸润,减少层合板的孔隙缺陷;添加0.05%(质量分数)的CNT后层合板的力学性能提高,使用超声波辅助真空罐注工艺制造的层板性能提高得更为明显;制造工艺对层合板性能的影响与纤维织物的结构紧密相关。     

Investigation on Thermal and Dimensional Stability of Epoxy Resin In-Situ Modified by Cyanate Ester Resin and Polydimethylsiloxane

The thermal and dimensional stability of epoxy resin (EP) in-situ modified by cyanate ester (CE) and polydimethylsiloxane (PDMS) are investigated by means of experiments and numerical simulation. Thermal gravimetric analysis (TGA) and differential scanning calorimeter (DSC) are used to analyze the heat resistance of the modified EP. The dimensional stability is characterized by the volume shrinkage of the series PDMS/CE/EP obtained by the density method. The chemical structure of the PDMS/CE/EP is analyzed by Fourier transform infrared spectroscopy (FTIR). The results of TGA and DSC indicate that the thermal stability of PDMS/CE/EP decreases firstly and then increases with the increase in the amount of CE. The addition of PDMS shows a slight effect on the thermal stability. The 40% CE makes the blending system exhibit the lowest initial decomposition temperature, which reduces by 15.5% and 40.8% compared with pure EP and CE, respectively. The FTIR results suggested that the influence of CE on the thermal stability of the modified EP is mainly ascribed to the generation of oxazolidinone ring with low thermal stability and the increase in the triazine ring with high thermal stability. The volume shrinkage measurement results show that the introduction of CE and PDMS are both beneficial to the improvement of the dimensional stability of the blending systems. The in-situ addition of 80% CE shows the lowest volume shrinkage of 6.11%. The thermal stress distribution of PDMS/CE/EP generated during the solidification process is simulated by the finite element analysis. The results suggested that the introduction of 80% CE into EP results in the lowest thermal stress in the blending system, which indicates that the system has the lowest volume shrinkage, which agrees well with the experimental results.